Turntable and vinyl terms: parts of a record player explained
A record player has three working parts: the deck, which spins the record on a platter set in a plinth; the tonearm, which carries the cartridge and stylus across the groove; and the phono stage, which raises the cartridge’s tiny signal to a level an amplifier can use. Setting one up comes down to three adjustments made in order: balance with the counterweight, then tracking force, then anti-skate.
16 terms Updated
The deck
Everything below the record has one job: turn it at a steady speed while passing on as little vibration as possible. The drive type draws most of the argument; the plinth and platter do much of the work.
- Plinth
- The plinth is the base of a turntable: the box or frame that holds the platter bearing, the motor and the tonearm. It keeps those three fixed relative to each other and keeps outside vibration away from the record.
- Suspended and unsuspended plinths both reach the top of the market, so the design tells you how a deck deals with vibration, not how good it is.
- Platter
- The platter is the heavy disc on a turntable that the record sits on and the motor turns at 33⅓ or 45 rpm. Its mass, the bearing beneath it and the mat on top all affect how steadily and quietly it spins.
- The platter, its bearing and the motor together set the figure spec sheets quote as wow and flutter, the speed wobble heard as wavering pitch; lower is better.
- Spindle
- The spindle is the short metal pin at the center of a turntable platter. The record’s center hole fits over it, which keeps the groove centered under the stylus. On many decks it is the top of the platter bearing’s shaft.
- If the pitch wavers on every record, suspect the spindle or the bearing under it; if it wavers on only one, that record was probably pressed off center.
- Belt drive
- A belt-drive turntable spins the platter with a rubber belt from a motor mounted off to the side, so the motor’s vibration is isolated from the record. It is the most common design in hi-fi turntables, favored for low noise.
- Lift the platter to check: a rubber loop round a motor pulley means belt drive, and the belt is the first part a secondhand buyer should budget to replace.
- Direct drive
- A direct-drive turntable mounts the platter directly on the motor shaft, with no belt. It starts and stops instantly and holds speed precisely, which made it the standard for DJs and broadcast, and modern versions are quiet enough for serious listening.
- Secondhand, the drive type changes what can fail: a direct-drive deck has no belt to wear out, but a failed motor or speed control board costs far more to put right than a belt.
The tonearm
The arm carries the cartridge across the record, and most of the parts people look up by name are on it. These three are the ones you handle or replace; the settings come later on this page.
- Tonearm
- The tonearm holds the cartridge and lets it track the record groove from edge to center while applying a small, set downward force. Its geometry, bearings and rigidity decide how accurately the stylus follows the groove.
- An arm with adjustable height, force and anti-skate leaves room for cartridge upgrades later; budget decks with fixed settings usually tie you to the cartridge fitted at the factory.
- Headshell
- The headshell is the small mount at the front of a tonearm that the cartridge bolts to. Some are part of the arm; others detach with a locking collar, so a cartridge can be swapped by changing the whole headshell.
- A detachable headshell lets owners keep a second cartridge ready, such as a mono cartridge or one for 78s, and change over without touching the four wires each time.
- Cueing lever
- The cueing lever raises and lowers the tonearm slowly, so the stylus lands in the groove gently instead of being dropped by hand. Raise the lever, move the arm over the record, then lower it; a damped mechanism controls the descent.
- It is the control you touch most often, so it is the one most worth testing on a secondhand deck: raise and lower it and watch for a slow, steady descent.
The cartridge
The cartridge turns the groove’s movement into a signal of a few millivolts or less, and the stylus is the only part that touches the record. Generator type and stylus shape are separate choices, often made on the same purchase.
- Stylus
- The stylus is the diamond tip that rides in the record groove. Mounted on a cantilever, it follows the groove’s wiggles and passes them to the cartridge. Its shape decides how much of the groove it reads; its condition decides whether it harms records.
- When a shop lists a cartridge as elliptical, Shibata or MicroLine, that is the stylus shape, and it is often the main difference between the cheaper and costlier models in one cartridge family.
- MM cartridge
- A moving magnet cartridge generates its signal with a tiny magnet on the end of the stylus cantilever that moves between fixed coils. It outputs a few millivolts, works with any standard phono stage and usually has a replaceable stylus.
- Any phono input labeled MM, or simply Phono, will run one with nothing to adjust, so it needs no extra box as long as the amplifier has a phono input.
- MC cartridge
- A moving coil cartridge puts tiny coils on the stylus cantilever and fixes the magnets, the reverse of a moving magnet design. The lower moving mass is prized for detail, but the output is far smaller and needs a phono stage with extra gain.
- Read the output figure before buying: around 0.5 mV or less needs an MC phono setting or a step-up transformer, while high-output models near 2 mV run from a standard MM input.
The settings
Three settings, made in this order, decide whether the stylus sits in the groove as its designer intended. The last two follow from one number: the tracking force the cartridge maker publishes.
- Counterweight
- The counterweight is the round weight on the back of a tonearm. It first balances the arm so it floats level, then, moved forward past that point, sets the stylus’s downward tracking force, usually read from a numbered ring on its front.
- Balance comes first because both later settings depend on it: a carelessly balanced arm gives a false tracking force reading, and anti-skate set to that reading is off too.
- Tracking force
- Tracking force is the downward weight of the stylus on the record, measured in grams and set with the tonearm’s counterweight. The cartridge maker specifies it, usually somewhere between 1.5 and 2.5 g for hi-fi cartridges. Set it to the maker’s figure.
- Look the figure up on the cartridge maker’s page, not in the turntable manual, which covers only the cartridge fitted at the factory; it is the number the other two settings follow.
- Anti-skate
- Anti-skate is a small outward force applied to a pivoted tonearm to counter skating, the pull that draws the stylus toward the center of the record. Set correctly, it keeps the stylus pressing evenly on both groove walls.
- A deck plays with it set to zero, which is why it is easy to miss during setup; the cost arrives slowly, as uneven wear on one side of the stylus and groove.
| Part | What it does | What you set or replace |
|---|---|---|
| Plinth | Holds the bearing, motor and arm in place; keeps outside vibration from the record | Leveling feet, where fitted; the springs on a suspended deck, now and then |
| Platter | Carries the record and turns it at 33⅓ or 45 rpm | The mat; the belt on belt-drive decks, when it stretches |
| Spindle | Centers the record under the stylus | Nothing; keep it clean and free of oil |
| Tonearm | Carries the cartridge and holds the stylus in the groove | Height, where adjustable; cartridge alignment |
| Headshell | Holds the cartridge at the front of the arm | Cartridge position in the slots, which sets overhang; the whole headshell, if detachable |
| Counterweight | Balances the arm, then sets tracking force | Balance to zero, then the cartridge maker’s recommended force |
| Anti-skate | Counters the pull of the stylus toward the center of the record | A dial or hanging weight, usually set to match the tracking force |
| Cueing lever | Lowers the stylus onto the record slowly | Lift height; damping fluid, if the arm drops too fast |
| Stylus | Traces the groove | Clean it every side or two; replace it when worn |
| Phono stage | Raises the cartridge signal to line level and applies RIAA equalization | MM or MC setting; gain and loading on better models |
The phono stage
A cartridge’s signal is far too small for an ordinary amplifier input, so it passes through a phono stage first. A system needs exactly one, plus a transformer only for some moving coil cartridges.
- Phono stage
- A phono stage boosts the tiny signal from a turntable cartridge to line level and applies the RIAA equalization that undoes the bass cut and treble boost applied when the record was cut. Without one, a turntable sounds faint and thin.
- On a spec sheet the useful figures are gain in dB, the loading options and signal-to-noise ratio, which counts for more here than on most boxes because of how much gain is applied.
- Step-up transformer
- A step-up transformer, or SUT, is a passive box that raises the signal of a low-output moving coil cartridge to the level a moving magnet phono input expects. It needs no power, and its gain is set by the ratio of its windings.
- It only makes sense with a low-output MC cartridge; an amplifier or phono stage that already has an MC setting does the same job without the extra box and cable.