Amplifier, DAC and source terms
A hi-fi system passes music from a source, such as a streamer, transport or DAP, through a DAC that turns data into an analog signal, to an amplifier that makes it strong enough for headphones or speakers. Most terms on this page name one of those jobs, or a box that combines several, such as an integrated amplifier or a receiver. The rest, such as Class D and R2R, describe how the circuits inside are built.
19 terms Updated
Sources
A source supplies the music. These three replace a phone or laptop at the start of the chain, and each sends digital audio on to a DAC, either inside the same box or in a separate one.
- Streamer
- A streamer is a network audio player that pulls music from streaming services or a home server and sends it to a DAC, over a wire or through a DAC built in. It replaces a laptop or phone as the source in a hi-fi system.
- On a spec sheet, check two lists: the services and protocols it supports, which decide what you can play, and its outputs, which show if a separate DAC is needed.
- Transport
- A transport reads music from a disc and sends it out as digital data for a separate DAC to convert. A CD transport is a CD player with digital outputs only, usually coaxial or optical, and no analog stage of its own.
- On a back panel, a transport has coaxial or optical outputs and no analog pair; a CD player with both can work either way, which makes it the more flexible purchase.
- DAP
- A DAP, or digital audio player, is a portable music player with its own DAC and headphone amplifier, built to drive headphones better than a phone. Most run Android, store lossless files and offer balanced output.
- Compare one with a phone and dongle on output power at your headphone’s impedance and on battery life, since those two figures separate them more than the DAC chip does.
DACs
Every digital source needs a DAC before the amplifier. The two design terms here describe the conversion method, and the dongle is the smallest form a complete DAC comes in.
- DAC
- A DAC, or digital-to-analog converter, turns the numbers in a digital file or stream into the analog voltage an amplifier and headphones or speakers can use. Every phone and laptop has one built in; a separate DAC aims to do the job better.
- Often bought as an upgrade and rarely the limiting part: check its inputs and outputs against your system before its measurements, which mostly clear the limits of hearing.
- Delta-sigma DAC
- A delta-sigma DAC converts audio by resampling it to a very high rate with only a few bits, then filtering the result, rather than converting each sample directly. Almost every DAC chip made today works this way, because it achieves very low distortion cheaply.
- Assume this unless the maker says R2R, ladder, multibit or NOS: nearly every DAC and dongle at every price converts this way.
- R2R/ladder DAC
- An R2R, or resistor ladder, DAC converts each sample directly through a network of precisely matched resistors, one step per bit. It was the original way to build a DAC and has returned as a boutique alternative to delta-sigma chips.
- Usually signaled by the words ladder, multibit or NOS on a product page; expect higher measured distortion than a delta-sigma design at the same price, which owners accept for the sound.
- USB dongle
- A USB dongle is a pocket DAC and headphone amplifier on a short cable. It plugs into a phone’s or laptop’s USB port, takes digital audio and drives headphones from its own socket, doing the job of the headphone jack most phones no longer have.
- Often the first external DAC people buy; for sensitive IEMs it is the whole chain, and its rated power at 32 Ω and 300 Ω shows how demanding a headphone it can take.
Amplifiers
These names describe how an amplifier’s jobs are split between boxes: choosing a source and setting the volume (the preamp), and driving the speakers (the power amp). Read them as packaging, not as quality tiers.
- Amplifier
- An amplifier takes a small audio signal from a source or DAC and makes it strong enough to drive headphones or speakers. Headphone amps deliver milliwatts into loads of roughly 16 to 600 ohms; power amps deliver tens or hundreds of watts into speakers.
- The umbrella term for this group; every other name here is an amplifier with jobs added or removed, so start from what your speakers or headphones need and choose the packaging second.
- Preamp
- A preamp, or preamplifier, selects between sources, controls the volume and passes a line-level signal on to a power amplifier. In a separates system it is the control center; an integrated amplifier builds one in.
- The control half of an amplifier sold on its own; if a box in your chain already has a volume control and the inputs you need, it is doing this job already.
- Power amplifier
- A power amplifier raises a line-level signal to the voltage and current that passive speakers need. Most have no volume control or input selector, so they take their signal from a preamp or a source with its own volume control.
- Rated by power into a stated impedance, usually 8 Ω and 4 Ω; compare that with your speakers’ sensitivity, since a few decibels of sensitivity outweigh large differences in watts.
- Integrated amplifier
- An integrated amplifier is a preamp and a power amplifier in one box: it switches between sources, sets the volume and drives passive speakers. It is the usual center of a two-channel hi-fi system, fed by sources such as a CD player, DAC or streamer.
- Its close relatives each add a source: a receiver adds radio or surround processing and a streaming amplifier adds a network player, so choose by which extras you would use.
- Monoblock
- A monoblock is a power amplifier with one channel in its own chassis. A stereo system uses a pair, one for each speaker, so each channel gets its own power supply and can sit close to the speaker it drives.
- The far end of splitting the amplifier into boxes: a preamp, then one power amplifier per channel, which buys power and freedom of placement at the cost of twice the hardware.
- Receiver
- A receiver is an amplifier with extra functions built in: a radio tuner in a classic stereo receiver, or surround-sound decoding, video switching and room correction in an AV receiver. One box replaces a preamp, power amp and several sources.
- The most complete box in this group, with preamp, power amp and sources together; it suits a system built around a TV, where a stereo integrated suits one built around music.
- Phono stage
- A phono stage boosts the tiny signal from a turntable cartridge to line level and applies the RIAA equalization that undoes the bass cut and treble boost applied when the record was cut. Without one, a turntable sounds faint and thin.
- The one box in this group built for a single kind of source: its gain and equalization suit only a turntable cartridge, so it always sits before the preamp, never after.
Amplifier designs
Two separate choices: the devices that amplify, tubes or transistors, and the class of the output stage, which sets how much power turns into heat. This group starts more forum arguments than the rest of the page combined.
- Solid-state
- Solid-state means an amplifier or other circuit built with transistors and integrated circuits rather than vacuum tubes. Nearly all modern audio electronics are solid-state; the term mostly comes up in contrast to tube designs.
- The default for decades; a spec sheet that does not mention tubes or valves is describing one, whatever class its output stage uses.
- Tube amplifier
- A tube amplifier uses vacuum tubes, also called valves, instead of transistors to amplify the signal. Tube amps measure worse than solid-state designs but are loved for a sound many describe as warm and full, and for the glow.
- Budget for the running costs as well as the price: replacement tubes every few thousand hours and, for fixed-bias designs, a bias check whenever the output tubes change.
- Class A
- A Class A amplifier keeps its output transistors or tubes conducting all the time, so the signal never has to hand over between devices. It is the simplest and, in theory, cleanest output stage, and also the least efficient: most of the power becomes heat.
- The class to expect in many headphone amps and every single-ended tube design; in a speaker amp, check whether the maker means pure Class A or only the first few watts.
- Class AB
- A Class AB amplifier uses two output devices that each handle one half of the waveform, with a small overlap so neither switches fully off. It is the standard design for most solid-state and tube power amplifiers, balancing efficiency with low distortion.
- If a speaker amp’s spec sheet names no class, it is almost always this or Class D, and the size of the heatsinks is a fair clue which.
- Class D
- A Class D amplifier switches its output devices fully on and off at a very high rate and filters the result back into an audio signal. It is over 90 percent efficient, which allows small, cool-running amplifiers with hundreds of watts.
- The usual class inside active speakers, subwoofers and streaming amps; a small, light amplifier rated at hundreds of watts per channel is almost certainly Class D.
| Design | Efficiency | Heat | Where you find it |
|---|---|---|---|
| Class A | 25 to 50 percent at best, far lower at normal listening levels | Hottest at idle; needs large heatsinks | Headphone amps, single-ended tube amps, a few speaker amps |
| Class AB | About 50 to 70 percent at full power, much less at listening levels | Warm; hotter the louder it plays | Most integrated amps, receivers and transistor power amps |
| Class D | Over 90 percent | Barely warm; no large heatsinks needed | Active speakers, subwoofers, compact integrated and streaming amps |
| Tube | Set by its class: single-ended designs are Class A, most push-pull designs Class AB | Hot; tubes wear and need replacing every few thousand hours | Preamps, headphone amps and speaker amps, often of modest power |