Speaker terms: drivers, cabinets and rooms
A speaker is drivers in a box: a woofer for bass, a tweeter for treble and a crossover that splits the signal between them, in a cabinet that is usually sealed or ported. Size and placement give the common types, bookshelf, floorstanding and subwoofer, and once they are set up, the room shapes the sound as much as any of these parts.
15 terms Updated
Drivers and crossovers
Most speakers divide the range between two or more drivers, a large one for bass and a small one for treble. The crossover sets where one hands over to the next.
- Woofer
- A woofer is the larger speaker driver that plays the bass. In a two-way speaker it also covers the midrange up to the crossover, usually somewhere around 1.5 to 3 kHz, and is then often called a mid-woofer or mid/bass driver.
- In a bookshelf speaker there is usually one, 4 to 6.5 inches across, and in a floorstander often two or more, which with the bigger cabinet accounts for most of the bass difference between them.
- Tweeter
- A tweeter is the small speaker driver that plays the treble, usually everything above a crossover point somewhere around 1.5 to 3 kHz. Most are domes about an inch across; ribbons, air motion transformers and horn-loaded compression drivers are the main alternatives.
- When you toe speakers in toward your seat, you are mainly aiming the tweeter: small angle changes alter the treble you hear far more than they alter the bass.
- Crossover
- A crossover splits an audio signal by frequency so each driver gets only the range it can play: bass to the woofer, treble to the tweeter. It is passive, inside the speaker after the amplifier, or active, splitting the signal before amplification.
- Spec sheets list its frequency as the crossover point; a speaker with two pairs of terminals has its passive crossover split into bass and treble halves, ready for bi-wiring.
Cabinets and ports
The box decides what happens to the sound from the back of the woofer, and that decides how the bass ends. These are the three main answers, and the ported box is the most common.
- Sealed enclosure
- A sealed enclosure is a speaker cabinet with no port, so the trapped air acts as a spring behind the driver. It gives tighter, more gradual bass than a ported box and sits happily near walls, but produces less deep bass for its size.
- Spotted by the absence of any port, front or back; the easier choice for a speaker that has to sit close to a wall or hand its lowest notes to a subwoofer.
- Bass reflex
- A bass reflex speaker has a port, a tube or slot in the cabinet, tuned so the air inside resonates and reinforces the bass near the speaker’s low-frequency limit. It is the most common enclosure because it gets more bass from a given box.
- Compared with the sealed box above, it trades a steeper bass roll-off for more output from the same size, and a rear port asks for more space from the wall.
- Passive radiator
- A passive radiator is a driver with no motor, just a cone and suspension, mounted in a speaker cabinet to do the job of a port. Air pressure from the active driver moves it, adding bass without the noise of a port tube.
- The usual answer in compact wireless speakers: look for an extra cone, often one on each side, that is not wired to anything and moves visibly on bass notes.
Sizes and types
These names describe size, shape and where the amplifier lives, not quality. A bookshelf pair with a subwoofer and a pair of floorstanders are the two common routes to full-range bass.
- Bookshelf speaker
- A bookshelf speaker is a compact speaker, usually a two-way with a woofer of about 4 to 6.5 inches and a tweeter, built to sit on a stand, desk or shelf. Most are passive; they sound best on stands, clear of walls.
- The usual starting point for a first stereo pair; include stands, or a solid surface at ear height, in the budget, since a pair placed low on a cabinet will not sound as designed.
- Floorstanding speaker
- A floorstanding speaker, or tower, is a tall speaker that stands directly on the floor. Its larger cabinet and bigger or extra drivers give deeper bass and more volume than a bookshelf speaker, at the cost of space, price and harder placement.
- The other route to full-range sound: one cabinet per side instead of a bookshelf pair plus a subwoofer, simpler to set up but less flexible about where the bass comes from.
- Subwoofer
- A subwoofer is a speaker dedicated to the lowest octaves, typically below 80 to 120 Hz, with a large driver and usually its own amplifier. It lets the main speakers hand off the bass they cannot reproduce and fills in the bottom of the room.
- An addition to either type above rather than a replacement; most include their own amplifier, which makes them active speakers with a single job.
- Active speaker
- An active speaker has its amplifiers built into the cabinet, usually one per driver, with the crossover working on the signal before amplification. Studio monitors have been active for decades; hi-fi has followed as streaming made the all-in-one system appealing.
- Can be bookshelf, floorstanding or subwoofer in shape; it needs a line-level source and a volume control somewhere instead of an amplifier, which changes the rest of the shopping list.
| Type | What it is | Bass | Placement | What else it needs |
|---|---|---|---|---|
| Bookshelf | Compact, usually two-way, with a 4 to 6.5 inch woofer | Typically about 6 dB down somewhere around 45 to 60 Hz | On stands at ear height, with some space behind | An amplifier, unless active |
| Floorstanding | Tall cabinet, often three-way or 2.5-way with two or more woofers | Deeper; often enough for most music without a subwoofer | On the floor, about 30 cm to 1 m from the wall behind to start | An amplifier, unless active |
| Subwoofer | Separate cabinet with a large driver, usually with its own amplifier | Only the lowest octaves, typically below 80 to 120 Hz | On the floor; its spot in the room matters more than for any other speaker | A line-level or speaker-level feed and a crossover setting |
| Active speaker | Amplifiers built into the cabinet, usually one per driver | Set by size and cabinet, as for passive speakers | As for the passive equivalent, plus a mains outlet | A source with a volume control |
Amplifiers and rooms
Passive speakers need an amplifier, and the speaker’s sensitivity sets how much power that takes. After that, the room changes the result more than the cabling does, and often more than the amplifier.
- Sensitivity
- Sensitivity says how loud a headphone or speaker plays for a given input: so many decibels per milliwatt or per volt for headphones, per watt at one meter for speakers. Higher numbers play louder from less power.
- The speaker figure to read before an amplifier’s power rating: every 3 dB less sensitivity needs twice the power for the same loudness.
- Power amplifier
- A power amplifier raises a line-level signal to the voltage and current that passive speakers need. Most have no volume control or input selector, so they take their signal from a preamp or a source with its own volume control.
- The box that drives passive speakers in a separates system; its rating means most when quoted at the lower impedance your speakers may dip to, often 4 Ω rather than 8 Ω.
- Receiver
- A receiver is an amplifier with extra functions built in: a radio tuner in a classic stereo receiver, or surround-sound decoding, video switching and room correction in an AV receiver. One box replaces a preamp, power amp and several sources.
- Often the amplifier in a home theater speaker system; its subwoofer output and bass management set the crossover between the main speakers and the subwoofer for you.
- Bi-wiring
- Bi-wiring runs two separate pairs of speaker cable from one amplifier channel to a speaker with two sets of terminals, one for its woofer section and one for its tweeter section. Measured differences are small, and listeners disagree about whether it is audible.
- Possible only on speakers with two pairs of terminals joined by jumpers; of the topics in this group, it has the smallest measured effect and the longest forum threads.
- Room treatment
- Room treatment is anything added to a listening room to control reflections and resonances: absorbing panels, bass traps in the corners and diffusers on the back wall. In a speaker system the room changes the sound more than most equipment does.
- Usually the largest change available in this group: a rug, a sofa and panels at the first reflection points alter what reaches your ears more than a different cable does.