Your rig deserves a home. Catalog your gear and get your own A-number. Free, always.

White cartoon mascot wearing glowing gold headphones, holding an open-back pair over a desk of small audio boxes and cables.

Headphone and IEM terms: drivers, designs and fit

Driver type gets most of the attention in headphone talk, but the design decides where you can wear a headphone and the fit decides much of the bass you hear. The drivers are dynamic, planar magnetic, electrostatic and balanced armature; the designs are open-back, closed-back and in-ear; and the fit comes down to ear tips and earpads.

13 terms Updated

Drivers

Six ways of turning a signal into moving air. The first four are distinct mechanisms, hybrid combines them, and bone conduction bypasses the eardrum. The type tells you more about size, power needs and price than about tuning.

Dynamic driver
A dynamic driver is the most common loudspeaker and headphone transducer: a coil of wire attached to a cone or dome, sitting in a magnetic field, that pushes the diaphragm back and forth when the music signal passes through it.
Treat it as the baseline for this list: when a spec sheet gives a driver size in millimeters and names no other type, the driver is almost always dynamic.
Planar magnetic
A planar magnetic driver is a thin, flat diaphragm with a printed conductive trace, suspended between magnets. The whole diaphragm is driven at once, instead of from a single voice coil as in a dynamic driver.
Found in full-size open headphones and, increasingly, in IEMs; on either, read the sensitivity figure first, since it predicts the amplifier you need better than the impedance does.
Electrostatic
An electrostatic driver moves an extremely thin, charged membrane between two perforated plates using high voltage rather than magnets. It needs a special energizer or amplifier, and is known for speed and delicacy in the treble.
The only type here that cannot plug into an ordinary headphone socket, so the cost of owning one always includes an energizer; in IEM listings the word means small tweeters inside a hybrid.
Balanced armature
A balanced armature is a tiny driver, long used in hearing aids, in which a pivoting metal reed moves a small diaphragm. Its size lets in-ear monitors pack several into one shell, each handling part of the frequency range.
Found almost only in IEMs, earbuds and hearing aids; a multi-armature set is the type most likely to change its tonal balance when moved to a source with a high output impedance.
Hybrid
A hybrid in-ear monitor combines two or more driver types, most often a dynamic driver for bass and balanced armatures for the mids and treble. A tribrid adds a third type, usually electrostatic tweeters.
The join between driver types is where a hybrid can go wrong, so a published measurement tells you more about one than its driver count does.
Bone conduction
Bone conduction headphones send vibration through the bones of the skull, usually from pads resting in front of the ears, so the ears stay open. They are built for runners and cyclists who need to hear traffic, not for sound quality.
Bought for keeping the ears open, so compare models on fit, battery life and water resistance before sound.
Headphone driver types compared
DriverHow it worksTypical strengthsTypical drawbacksIn the catalog
DynamicA voice coil on a cone or dome moves in a magnetic fieldInexpensive, usually sensitive, bass often described as having impactThe cone can flex and ring at high frequencies1,932 products
Planar magneticA conductive trace across a flat film, suspended between magnetsLow bass distortion, level down into the sub-bassHeavier; often low sensitivity, so many need an amplifier247 products
ElectrostaticA charged film between two perforated plates, driven by high voltageVery low distortion, extended and even trebleNeeds a dedicated energizer; expensive; sensitive to dust and damp54 products
Balanced armatureA pivoting metal reed drives a tiny diaphragmSmall enough to fit several in one IEM shellBass often described as lacking impact; can change sound with the source405 products
HybridTwo or more driver types and a crossover, usually dynamic bass with armatures aboveEach driver plays the range it handles bestThe drivers must blend at the crossover362 products
Bone conductionPads in front of the ears vibrate the bones of the skullEars stay open to traffic and voicesLimited bass and volume; leaks sound

Designs

These terms describe what surrounds the driver, and they decide where a headphone can be used before anyone hears it. Most driver types above turn up in more than one of them.

Open-back
Open-back headphones have earcups that let sound pass through the outside, usually through a grille. They leak sound both ways, so they are for quiet rooms, and they are widely preferred for a spacious, natural presentation.
Look for a grille across the outside of the cup. It is the only design in this group that blocks almost no outside sound, so treat it as a home headphone.
Closed-back
Closed-back headphones have sealed earcups that keep sound in and much of the outside world out. They suit commuting, offices and recording, and usually give stronger bass than open designs, at some cost to spaciousness.
The full-size choice for anywhere noisy or shared. Product pages sometimes say semi-closed: a mostly solid cup with small vents, which isolates a little less than a fully sealed one.
IEM
An IEM, or in-ear monitor, is an earphone that seals in the ear canal with a silicone or foam tip. Born as stage monitoring for musicians, IEMs, especially at the budget end, are among the most competitive parts of the headphone market.
Needs no headband and often isolates as well as a closed-back, but its sound depends on fit more than any other design here, so expect to try more than one tip size.
Wireless
Wireless headphones and speakers receive audio over Bluetooth or Wi-Fi instead of a cable, with a battery, DAC and amplifier built in. They trade some fidelity and the ability to upgrade parts for convenience and features such as noise cancelling.
Describes the connection, not the shape: open, closed and in-ear designs can all be wireless, and then the maker’s own DAC, amplifier and tuning replace any you might choose.

Fit and tweaks

Three inexpensive ways to change how a headphone sounds without replacing it. Tips and pads alter the seal and the distance to the ear, which shows on a measurement; crossfeed changes the stereo picture instead.

Ear tips
Ear tips are the soft silicone or foam sleeves that fit over an IEM’s nozzle and seal it in the ear canal. The seal decides the bass, the isolation and part of the treble, so changing tips changes the sound.
Tips are to IEMs what pads are to full-size headphones, with one difference: you choose the size, so a poor seal is often a fitting problem rather than a design one.
Earpads
Earpads are the cushions on a headphone’s cups that rest on or around the ears. They set the distance and angle between driver and ear, and the seal around it, so a pad change can shift the bass and treble by several decibels.
Pads also decide comfort over a long session: leather and protein leather trap heat against the skin while velour breathes, so the better-sealing pad is not always the one you keep wearing.
Crossfeed
Crossfeed is a headphone feature that mixes a filtered, slightly delayed share of each channel into the other, imitating the way each ear hears both loudspeakers in a room. It softens hard-panned stereo and makes some recordings less tiring.
Try it free in software before paying for an amplifier with a crossfeed switch; recordings with instruments panned hard to one side show the effect most clearly.

Guides that go further

Other topics