Your rig deserves a home. Catalog your gear and get your own A-number. Free, always.

How to build a signal chain for vinyl

Four things follow the record, in order: cartridge, phono stage, amplifier, and speakers or headphones. Use exactly one phono stage, which may already be inside your turntable or amplifier. With none the sound is quiet and thin; with two, loud and distorted. Start with a moving magnet cartridge, connect the ground wire and set the tracking force its maker gives.

Updated 15 min read

See the chart in full

Who this is for

Anyone who has bought a turntable, or is about to, and wants to know what has to sit between the record and their ears. It also suits anyone whose turntable is connected and sounds wrong: faint, thin, distorted or humming. Most of those faults come down to a box missing, a box doubled or a wire left off, and each takes a minute to check.

It is not a buying guide. The few products named are examples of a type, with no ranking and no prices. Suitcase players and all-in-one units with speakers built in are left out, since they already contain the whole chain.

The chain, from groove to ear

Every vinyl system has the same six links in the same order, however many boxes they are spread across. The diagram below names them and gives each one’s job.

What changes from one system to the next is which links share a box. A turntable can contain the phono stage. A receiver can contain the phono stage and the amplifier. Active speakers contain the amplifier. The four arrangements further down are this one chain packed four ways, and whether the platter is turned by a belt or by direct drive changes nothing about the order.

  1. Stylus

    A diamond tip that follows the groove

  2. Cartridge

    Turns movement into a few millivolts

  3. Turntable

    Turns the record; its arm carries the signal out

  4. Phono stage

    Adds 40 to 60 dB of gain and RIAA equalization

  5. Amplifier

    Sets the volume; may be inside active speakers

  6. Speakers or headphones

    Turn the signal back into sound

Why a phono stage is needed

A cartridge’s output is tiny. A typical moving magnet cartridge gives about 5 mV, a high-output moving coil about 2 mV and a low-output moving coil about 0.3 mV. The inputs on an amplifier marked CD, AUX or LINE are built around a nominal level of about 300 mV, and a CD player or DAC puts out about 2 V at full level. These are typical published figures, the kind makers quote for a standard test tone, and not measurements of ours; loud passages run higher. The chart uses a log scale because the largest figure is nearly 7,000 times the smallest.

Closing the gap takes gain: about 40 dB for moving magnet, which multiplies the voltage by 100 and turns 5 mV into 500 mV, and about 60 dB for low-output moving coil, which multiplies it by 1,000 and turns 0.3 mV into 300 mV. Makers land close to those round numbers. Our catalog records the Cambridge Audio Alva Duo at 39 dB for moving magnet and 60 dB for moving coil, and the Schiit Mani 3 with a choice of 30, 40, 50 or 60 dB.

Gain is half the job. Records are cut with the bass turned down by up to about 20 dB and the treble turned up by a similar amount, which keeps the groove narrow and lets surface noise be turned down again on playback. The phono stage applies the opposite curve, called RIAA equalization. Without it you hear the record as it was cut, with almost no bass and far too much treble. That is the thin sound, and a tone control does not repair it.

All that gain also amplifies any hum picked up before it. That is why the cable from the turntable is kept short, and why the ground wire in the setup section matters.

Typical signal levels along a vinyl chain

By typical published figures, a cartridge gives roughly 0.3 to 5 mV, against about 300 mV at a line input and 2 V from a CD player or DAC at full level.
  1. Low-output moving coil
    0.3 mV
  2. High-output moving coil
    2 mV
  3. Moving magnet
    5 mV
  4. Line level, nominal
    316 mV
  5. Moving magnet after 40 dB
    500 mV
  6. CD player or DAC, full level
    2,000 mV

Bar lengths are on a log scale, so each step along is a multiple, not an equal amount.

Use exactly one phono stage

The phono stage can be in any of three places, and the back panels tell you which you have.

In the turntable. Look for a small switch marked PHONO and LINE. At LINE the built-in stage is working and the output can go to any ordinary input. At PHONO the stage is bypassed and the raw cartridge signal comes out. The Audio-Technica AT-LP120XUSB has this switch. The Technics SL-1500C is listed in our catalog with separate phono and line outputs, which does the same job.

In the amplifier. An input labeled PHONO, usually with a screw terminal marked GND beside it, has a phono stage behind it. Inputs labeled CD, AUX, TAPE, TUNER or LINE do not.

In a box of its own, wired between the two.

Where it sits decides which of the arrangements below is yours: in the turntable is arrangement 1, in the amplifier arrangement 2, in its own box arrangement 3. Arrangement 4 is any of them ending in headphones.

With no phono stage anywhere, the sound is very quiet even with the volume turned well up, and thin, with almost no bass. With two, which happens when a turntable set to LINE is plugged into a PHONO input, it is loud, boomy and distorted from the first touch of the volume control. Turn the volume right down before you move the switch or a cable: going from no stage to one raises the level about a hundredfold.

Of the 109 turntables in our catalog, 63 have this recorded, and 46 of the 63 have a phono stage built in. The 17 without one include the Rega Planar 3, the Pro-Ject Debut Carbon EVO and the Fluance RT85. That is a count of our records, which lean toward lower-priced decks, and not the share of all turntables on sale. Check the back of yours.

Phono stage built in, 109 turntables in the catalog

Of the 63 turntables with this recorded, 46 have a phono stage built in and 17 do not, and for another 46 we hold no record.
  1. Phono stage built in
    46
  2. No phono stage
    17
  3. Not recorded
    46

Arrangement 1: a turntable with a phono stage into active speakers

The fewest boxes. The turntable’s switch is at LINE, one RCA cable runs to a pair of active speakers, and the volume control is on the speakers. It suits a first system, a small room or a shelf.

Some active speakers have a PHONO input of their own, and that is where this arrangement goes wrong. Use that input with the turntable at PHONO, or an ordinary input with the turntable at LINE. Not both. The other cost comes later: changing any one link means switching the built-in stage off and adding a box.

  1. Cartridge

    Moving magnet

  2. Turntable

    Phono stage inside, switch at LINE

  3. Active speakers

    Amplifier and volume control inside

Arrangement 2: a turntable into an amplifier with a phono input

One box does three jobs: phono stage, volume control and power. The turntable’s RCA cable goes to the input marked PHONO and its ground wire to the GND screw beside it. If the turntable has a stage of its own, set its switch to PHONO so that the amplifier’s is the only one working.

It suits anyone who owns a stereo amplifier or receiver with the input, or can inherit one. Stereo models from the decades when records were the main source mostly have it; among current amplifiers, and AV receivers in particular, it comes and goes. These inputs are almost always made for moving magnet cartridges, which is no limit on a first system.

  1. Cartridge

    Moving magnet

  2. Turntable

    Switch at PHONO, if it has one

  3. Amplifier or receiver

    PHONO input, ground wire to GND

  4. Passive speakers

    Speaker cable from the amplifier

Arrangement 3: a separate phono stage into an amplifier

The phono stage is its own box. The turntable’s cable and ground wire go to it, and its output goes to any input on the amplifier except PHONO, or to active speakers in place of an amplifier. It suits the owner of an amplifier with no PHONO input and a turntable with no stage, the owner of a moving coil cartridge, and anyone who wants a quieter or more adjustable stage than the one built in.

Check which cartridges a stage accepts. The Rega Fono MM MK5 and U-Turn Audio Pluto 2 are for moving magnet, and the iFi ZEN Phono 3 takes both types. Then keep the box and its input cable away from the amplifier’s power transformer and from power adapters, because this is the most hum-sensitive point in the system.

  1. Cartridge

    Moving magnet or moving coil

  2. Turntable

    Switch at PHONO, if it has one

  3. Phono stage

    Ground wire attaches here

  4. Amplifier or receiver

    Any line input: CD, AUX or TAPE

  5. Passive speakers

    Speaker cable from the amplifier

Arrangement 4: vinyl into headphones

A phono stage’s output is a line-level signal with no volume control, and it is not built to drive headphones, so a headphone amplifier goes after it. A turntable with a built-in stage shortens the chain by a box: LINE output straight into the headphone amplifier. A few phono stages include the headphone amplifier; our catalog records one in the Cambridge Audio Alva Duo. And if you already have arrangement 2 or 3, the headphone socket on the amplifier or receiver is the same chain with nothing to buy.

It suits late listening and rooms with no space for speakers, and it removes the feedback problem described under setup. In exchange, headphones show up hum, hiss and surface noise that speakers across a room let pass, so the ground wire and a clean record count for more here.

  1. Cartridge

    Moving magnet or moving coil

  2. Turntable

    Switch at PHONO, if it has one

  3. Phono stage

    Ground wire attaches here; no volume control

  4. Headphone amplifier

    Sets the volume

  5. Headphones

    Start with the volume at minimum

Moving magnet or moving coil

Start with moving magnet. Its output suits every PHONO input and every built-in stage, and when the stylus wears out you pull it off and push on a new one. The Audio-Technica AT-VM95E and the Ortofon 2M Red are examples: each has a stylus you can replace at home, and each body accepts a finer stylus from the same family later.

A low-output moving coil asks three things of the phono stage. It needs about 60 dB of gain where moving magnet needs 40. It needs the stage to be quiet, because 20 dB more gain makes the stage’s own hiss 20 dB louder. And it needs a loading setting: moving magnet inputs present a standard 47 kΩ, while moving coil makers specify a much lower figure, often around 100 Ω, and stages built for the type let you choose. The Denon DL-103 is a low-output design, 0.3 mV by its maker’s figure. Its stylus, like that of most moving coils, cannot be replaced at home.

There are two ways to use a moving coil with a moving magnet input. A high-output moving coil such as the Denon DL-110 is wound to give enough voltage by itself. Or a step-up transformer goes between a low-output cartridge and the input: a passive box that raises the voltage by its turns ratio, 20 dB for a ratio of 1:10, and needs no power.

We take no side on which type sounds better. Moving coil supporters describe more detail from the lighter moving parts. Others point out that a good moving magnet with a fine stylus, properly set up, is hard to beat for the money. Listeners disagree about how much of what they hear is the generator and how much the stylus on the end of it, and the disagreement is in good health.

Setting it up

Level the turntable first. Put a small bubble level on the platter and adjust or shim the feet until it reads level in both directions. On a tilted deck the arm is pulled toward one side of the groove, and the stylus and record wear unevenly.

Set the tracking force to the figure the cartridge’s maker gives. It is usually a range somewhere between 1.5 and 2.5 g with a recommended value inside it, and our glossary entry on the tonearm describes how to balance the arm and dial it in. Too much force wears the stylus and the record faster and strains the cartridge’s suspension. Too little is not the safe side. A stylus that is too light loses contact with the groove wall on loud passages and strikes it on the way back, which you hear as distortion and which damages the groove. If in doubt, use the maker’s recommended value and not the bottom of the range, and confirm it with a stylus gauge. Then set the anti-skate to match. Some entry-level decks have the force fixed at the factory and no adjustment; leave those as they are.

A cartridge fitted at the factory is already aligned, and changing only the stylus does not disturb it, though the tracking force needs checking again. A cartridge you fit yourself has to sit square in the headshell at the distance the arm’s maker specifies, set with the card gauge supplied with the turntable or a printed alignment protractor.

Connect the ground wire. If the turntable has a thin separate wire with a forked end, fasten it under the GND screw on whichever box holds the phono stage. A steady low hum that rises with the volume control and is there with the record stopped usually means this wire is off or loose. Some turntables with a built-in stage have no ground wire and need none; if yours has one, connect it as the manual says.

Keep the turntable away from the speakers. The stylus cannot tell a shaking turntable from a moving groove, so whatever the speakers shake comes out of them again. Mild feedback thickens the bass. Strong feedback is a low howl that builds as the volume rises; turn the volume down at once if you hear it. Put the turntable on a rigid, level surface that the speakers do not share, out of the room’s corners, and as far from a subwoofer as the cables allow. On a springy floor where footsteps make the stylus jump, a wall shelf is the usual cure.

Turn the volume down before you lower or lift the stylus and before you change any cable, and lower the arm with the cue lever. A stylus landing or a plug pulled at high volume makes a thump that can damage speakers. With headphones, take them off first.

When it sounds wrong

Find what you hear in the left column. The first two rows are the missing phono stage and the doubled one.

What you hearLikely causeWhat to do
Very quiet and thin, with almost no bassNo phono stage in the chainSet the turntable to LINE, use a PHONO input, or add a phono stage
Loud, boomy and distorted at low volume settingsTwo phono stagesSet the turntable to PHONO, or move its cable to a line input
Full tone but very quiet, with a moving coil cartridgeA low-output moving coil into a moving magnet inputUse a stage with a moving coil setting, or add a step-up transformer
Steady hum, there with the record stoppedGround wire off or looseFasten it under the GND screw on the box with the phono stage
Hum that changes as the arm crosses the recordCartridge picking up a nearby transformerMove the turntable away from the amplifier and power adapters
Low howl or boom that builds with volumeFeedback from the speakersTurn down, then move the turntable off the speakers’ surface and further away
Distortion on loud passages, or skippingTracking force too low, or a dirty or worn stylusReset the force to the maker’s figure; clean or replace the stylus
One channel missing or cracklingA loose plug or headshell leadReseat the RCA plugs and, with the volume down, the headshell

What matters and what does not

In rough order of effect on a first chain, largest first.

The cartridge and the state of its stylus. It is the only part that touches the record, and the shape and condition of the stylus decide how much of the groove is read and how cleanly. Condition comes first. A worn or chipped stylus distorts and damages every record it plays, so on a second-hand turntable with an unknown history, replace the stylus before playing records you care about. Our glossary gives 300 to 1,000 hours as a rough life.

The speakers or headphones come second. As in any system, they change the sound more than the electronics in front of them.

Setup is third and costs almost nothing. No later link in the chain can repair what a badly set arm does at the groove, and a clean record and stylus belong here too.

The phono stage does measurable work: its hiss and hum are amplified along with the music, and its equalization can be accurate to a fraction of a decibel or tilted. A basic built-in stage is enough to start with, and replacing it is the usual first upgrade. How far the differences go beyond noise and accuracy is disputed among listeners.

Drive type sits lower. Modern belt-drive and direct-drive turntables both measure well, and the arm and cartridge matter more.

Cables are near the bottom, with one exception that is measured. The cable between a moving magnet cartridge and the phono stage adds capacitance, and too much of it shifts the treble, so that cable should be short, shielded and the one the turntable’s maker supplied or specified. Beyond that, measured differences between competently made RCA cables over a meter or two are very small. Some listeners report hearing differences, and we do not claim to settle it.

Mats, clamps, record weights and isolation feet have devoted owners and no agreement on what they do, a combination the hobby has always found workable. None of them is needed to get a first chain right.

How we know

The signal levels are standard published figures, not measurements of ours: cartridge outputs are quoted for a 1 kHz tone at a standard groove velocity, 316 mV is the nominal line level for home equipment, and 2 V is the usual full-level output of a CD player or DAC. Individual products sit either side of each figure, and the gain and equalization figures match our glossary.

The products named were checked against their makers’ pages in November 2026. That is where the cartridge types, the output figures and the cartridge types each phono stage accepts come from, because the catalog does not record whether a cartridge is moving magnet or moving coil, or its output voltage, for any of the 158 it lists.

The counts come from our records of 109 turntables, 158 cartridges and 37 phono stages. They are counts of listings, and some decks are listed once per color. Whether a turntable has a phono stage built in is recorded for 63 of the 109: 46 with and 17 without. The 46 with nothing recorded include nine Rega, nine Technics and four Luxman models, and 16 of the 46 with a stage are Audio-Technica listings, so the records lean toward lower-priced decks and 46 of 63 should not be read as the share of all turntables on sale. Outputs are recorded for 48 turntables, of which 16 list Bluetooth, and gain for four of the 37 phono stages.

We recommend no products and give no prices. A list price is recorded for 50 of the 109 turntables, 49 of the 158 cartridges and two of the 37 phono stages, and list prices in this part of the catalog have not been checked against makers’ sites. That is too thin to build picks on.

The setup advice follows what cartridge and turntable makers ask for in their own instructions. Where the manual for your turntable or cartridge gives a different figure or step, follow the manual.

Common questions

Can I plug a turntable straight into powered speakers?

Yes, if there is a phono stage in the turntable or in the speakers. If the turntable has a PHONO/LINE switch, set it to LINE and use any ordinary input. If only the speakers have an input marked PHONO, use that. With a stage in neither, the sound is very quiet and thin, and a separate phono stage between the two fixes it. Of the 63 turntables in our catalog with this recorded, 46 have one built in.

Is the phono input on a receiver good enough?

For a first system with a moving magnet cartridge, yes. It does the same two jobs as a separate phono stage: about 40 dB of gain and RIAA equalization. Try it before buying anything. If you hear no hum or hiss from your seat at normal volume with the record stopped, it is doing its work. A separate stage becomes necessary with a low-output moving coil cartridge, which most built-in inputs cannot amplify enough.

Can I use a Bluetooth turntable with a hi-fi system?

Yes, and usually by cable as well as by radio. Of the 16 turntables in our catalog that list Bluetooth among their outputs, 15 list an RCA connection, so the same deck can feed an amplifier or active speakers. Over Bluetooth the signal is digitized and compressed on the way, which some owners feel defeats the purpose and others find gets the record played. Where recorded, each has a phono stage built in, so use a line input.

Do old records need a different stylus?

Only 78s do. LPs and 45s, mono or stereo, play with a standard stylus. Shellac 78 rpm records have a much wider groove and need a stylus with a tip radius of about 3 mil, several times a standard tip’s, on a turntable with a 78 speed. The Ortofon 2M 78 is a cartridge made for them. Do not play an LP with a 78 stylus, or a 78 with a standard one; neither fits the other’s groove.

Related guides