Your rig deserves a home. Catalog your gear and get your own A-number. Free, always.

Specs & measurements

Headroom

Also called amplifier headroom, dynamic headroom

Headroom is the margin between the level a system normally works at and the most it can deliver before it clips. On audiophila. it means how many decibels above 100 dB SPL an amplifier can drive a given headphone; 10 dB or more is enough.

80 dB SPL9010011012097 dB/mW headphoneloud peak, 100 dB+10 dB is enough200 mW amp120 dB: 20 dB headroom10 mW amp107 dB: only 7 dB, short
Headroom for a 97 dB/mW headphone: an amplifier rated at 200 mW into its impedance drives it to 120 dB SPL, 20 dB above a loud 100 dB peak, while a 10 mW one reaches 107 dB, only 7 dB above. 10 dB or more is enough.

Music is not steady. Drum hits and orchestral climaxes can rise 10 to 20 dB above the average level, so a system that plays the average comfortably still needs reserve for the peaks. Without it the amplifier clips: the tops of the waveform are cut off, which sounds harsh and strained.

Our amp guide uses a fixed version of the idea. It takes 100 dB SPL as a loud peak, works out from the maker’s rated output and the headphone’s sensitivity how far above that the amplifier can go, and treats 10 dB or more as enough. A 97 dB/mW headphone needs 2 mW for 100 dB; an amplifier rated at 200 mW into its impedance reaches 120 dB, which is 20 dB of headroom.

More headroom than you use buys nothing audible. An amplifier with 30 dB in hand sounds the same at a normal level as one with 12, provided neither is near clipping; the extra covers quiet recordings and insensitive headphones. Recording and digital processing use the same word for the space left below 0 dBFS, the point at which a digital signal clips, and gain set too high anywhere in a chain uses it up.

Common questions

How much headroom should you leave when recording?

At 24-bit, a common target is an average level around −18 dBFS with peaks between about −12 and −6 dBFS. That leaves room for an unexpectedly loud moment, and the format’s noise sits so far down that recording quieter costs nothing audible. On many studio converters −18 dBFS lines up with the nominal analog operating level, which is why the figure is so widely used. Clipped takes cannot be repaired; quiet ones can be raised.

How much headroom should a mix leave for mastering?

A common rule of thumb is peaks around −6 dBFS with no limiter on the master bus. The exact figure matters less than it did, since a mix exported as a 32-bit float file can be turned down afterward without damage. What matters is that the mix has not clipped and has not already been squashed by heavy limiting, because dynamic range removed at that stage cannot be put back.

How much amplifier headroom do speakers need?

Enough for the peaks, which takes far more power than the average. A speaker with a sensitivity of 87 dB playing an average of 85 dB at 1 m uses about 0.6 W; peaks 20 dB above that need about 63 W. That is why a 100 W amplifier that barely works on average levels is still a sensible match, and why a 20 W one can clip on the same music.

What does headroom mean on a guitar amplifier?

It means how loud the amplifier plays before it starts to distort. Guitarists who want a clean sound at band volume look for plenty of headroom; those who want the amplifier’s own overdrive at a manageable volume prefer little. The idea is the same as in hi-fi, but the goal differs: in a guitar amplifier distortion is often part of the instrument, while in playback equipment it is always a fault.

Related terms