Open-back wired headphones from Shure with 40mm dynamic drivers, released in 2011 and listed at $499. They weigh 268 g and use dual-exit detachable cables with MMCX connectors.
Headphones · Open-back · Dynamic · 65 Ω · 96 dB/mW
No members own one yet. Own one? Add it to your collection
On sale
15 yrs
since 2011
Impedance
65Ω
96 dB/mW
Rating
—
be the first to rate
Owners
0
be the first
Measured
1
frequency curve
MSRP
$499
no live price today
About
The yoke is aluminium alloy and the grilles are stainless steel. The box holds an extra pair of velour ear pads, two detachable cables, a threaded 6.3 mm adapter and a zippered hard travel case.
Against a common listening target, the mids (250 Hz–2 kHz), treble (5–10 kHz) and air (10–20 kHz) all sit within 1 dB of it. The upper mids (2–5 kHz) sit 2.3 dB above the target and sub-bass (20–60 Hz) 7.7 dB below.
Its 65 Ω impedance and 96 dB sensitivity come with a design optimised for external headphone amplifiers. A spare set of pads is the hobby's idea of a thoughtful present.
Price tracker
No current Amazon price · new and used prices, checked daily. See today's price on Amazon ↗
New, lowest
$623.75
30-day low
MSRP
$499
list price
The technical bits
Sound
Specs
65Ω
96 dB/mW
Driver Type
Driver Size
40mm
10Hz-30kHz
Weight
268g
Design
No
Cable
Detachable
What to pair it with
All of these have enough power for the Shure SRH1840 (65 Ω, 96 dB/mW). 100 dB needs about 2.5 mW; with our 10 dB reserve, about 25 mW.

FiiO
K19
Rated 2.3 W SE, 8 W balanced into 32 Ω.
6.35 mm and 4.4 mm balanced.

Singxer
SA-1
Rated 5.5 W balanced into 32 Ω.
One balanced output.

Violectric
HPA V222
Rated 3.4 W balanced into 50 Ω.
One Headphone outputs (balanced and 6.3 mm) output.

FiiO
K17
Rated 1.85 W SE, 4 W balanced into 32 Ω.
6.35 mm and 4.4 mm balanced.
We compare the voltage these headphones need to reach 100 dB with what each amp is rated to deliver, and look for a 10 dB reserve on top. The ratings come from the makers' own spec sheets. This is about power only. It says nothing about how the pair sounds, and it doesn't cover amp output impedance. Makers rate power at their own distortion limit, often 1% THD+N, so clean power can be lower. Power is shown single-ended (SE) and balanced where an amp has both. Figures at different loads are not directly comparable, so we compare voltage. The target is our policy, not a physical limit.
Frequency-response effects matter most for low-impedance or multi-driver in-ear monitors, and sensitivity is a single-frequency figure.
Shure SRH1840: 65 Ω, 96 dB/mW (source)
FiiO K19
Singxer SA-1
Compare
Where to buy

Shure SRH1840
Headphones
As an Amazon Associate audiophila. earns from qualifying purchases.
We like to keep the amps flowing. We could run ads, but we prefer affiliate links—they're what we'd click anyway to dig deeper. Thanks for the support!
Violectric HPA V222
FiiO K17
audiophila. community ranks
Current ownership and wishlists, ranked within each category. These measure community participation, not sales or sound quality.
Snapshot: 2026-11-16 UTC · All regions · Method v1
Not enough community data to publish ranks yet.
Not enough community data to publish ranks yet.
History begins with the first daily snapshot. A chart appears after two observations.
Each member counts once per model, and once per brand in a category. Previous ownership is excluded. Suspended members and unapproved catalog entries are excluded. Variants with a parent model are excluded. An entry needs at least three members, and its category needs three eligible entries, before a rank is shown. Ties share a rank; the next position skips the tied entries. Each denominator is the eligible comparison group on that day. Brand-page model positions remain category ranks, not ranks across unrelated gear. History records observed daily positions, with gaps preserved. Up to ten entries per category and metric are displayed.